A multiband SSr diode RF rectifier with an improved frequency ratio for biomedical wireless applications

Scientific Reports volume 13, Article number: 13246 (2023) Cite this article

268 Accesses

Metrics details

This paper described a four-band implantable RF rectifier with simplified circuit complexity. Each RF-rectifier cell is sequentially matched to the four operational frequencies to accomplish the proposed design. The proposed RF rectifier can harvest RF signals at 1.830, 2.100, and white space Wi-Fi bands between 2.38 to 2.68 GHz, respectively. At 2.100 GHz, the proposed RF harvester achieved a maximum (radio frequency direct current) RF-to-DC power conversion efficiency (PCE) of 73.00% and an output DC voltage \(V_{DC}\) of 1.61 V for an RF power of 2 dBm. The outdoor performance of the rectenna shows a \(V_{DC}\) of 0.440 V and drives a low-power bq25504-674 evaluation module (EVM) at 1.362 V. The dimension of the RF-rectifier on the FR-4 PCB board is 0.27\(\lambda _{g}\) \(\times\) 0.29\(\lambda _{g}\). The RF-rectifier demonstrates the capacity to effectively utilize the frequency domain by employing multi-band operation and exhibiting a good impedance bandwidth through a sequential matching technique. Thus, by effectively controlling the rectenna’s ambient performance, the proposed design holds the potential for powering a range of low-power biomedical implantable devices. (BIDs).

Low-power embedded devices are becoming increasingly popular in a variety of consumer and industrial applications1,2. Biotelemetry, drug proportion, and allocation are some of the impacts BIDs technology made in the healthcare profession3,4. Recent advancements in materials and manufacturing have produced a novel, softer, adaptable devices with lower-impedance electrodes5,6,7. Since the technology’s inception, traditional batteries and physical interconnecting cables have been employed in these implants4,8. Because of their short lifespan, the batteries must be revised after a single installation. However, a patient must undergo an uncomfortable, expensive, and unpleasant procedure to change these batteries6,7,9. Additionally, the interconnecting wires are unsafe and can lead to other infectious diseases10. Several techniques have been established to extract energy from various sources, including vibration, acoustic, sound, light, pressure, and heat, to address these issues and constraints11,12,13,14,15. The radio frequency (RF) waves can be harnessed to operate electrical components and replenish the implant’s batteries8. Thus, ambient electromagnetic (EM) sources are becoming more popular for powering biomedical implants16. It is crucial to harvest these sources because of the relatively low signal amplitude and the significant power needed to drive biomedical implants17. A configurable wireless power transmitter (WPT) can simply be employed as a signal source in implants when potential operating power is desirable18. The WPT can extend the battery’s lifetime of the implantable medical devices (IMDs) and ease patients’ pain during surgery8,19. Several studies on the WPT’s, such as microwave radiation and near field coupling16,17,19, have been introduced based on the various application condition. The near field coupling mechanism often outperforms the microwave radiation in terms of the transmission range, but is larger in size12,18. Thus, a potential mechanism for the miniaturized IMDs is WPT-based microwave radiation16,17. Figure 1, demonstrate how a WPT depends on the coupling between the transmitter and receiver. The WPT microwave receiving segment requires an implanted antenna and RF rectifier to receive and transform the radiated RF signal into a DC source7. The regulated characteristics of the transmitter have made the WPT evolve as a potential solution to the traditional ambient sources for charging and powering the implants14,16. A power source and a rectenna make the WPT system. Thus, biomedical implants stand to benefit significantly from RF energy harvesting due to its various advantages: wireless power transmission, prolonged battery lifespan, miniaturization capabilities, improved dependability, scalability, and environmental sustainability2,18. These benefits lay the groundwork for enhanced and patient-centric implantable medical devices, propelling healthcare advancements and elevating patients’ quality of life.

Various implantable medical devices and their physical location inside human body.

Most WPT commercial transmitters have preset signal intensities; the rectenna side need to be designed to capture the least amount of available signal efficiently. Thus, to efficiently harvest a range of accessible sources, an efficient rectifier is required. The authors in20 demonstrate a 0.915 GHz mm-sized rectenna for a deep-brain stimulation mechanism. The radiated energy from the source is received using interconnected rectenna elements. At an input power of 30 dBm, the implant harvester reported a highest efficiency is 59.70%, at the cost of a limited bandwidth (BW). The authors in21 and22 describe a relatively compact planar inverted-F (PIFA)-based implantable rectenna. The radiating element is achieved through capacitive loading by introducing a short-pin in22 and spiral patches in21. A wireless power link comprising an implantable rectifier is investigated in22. The findings demonstrate that the approach achieved higher DC power at the expense of a narrow-BW and high \(P_{in}\). The authors in23 uses an external WPT to deliver power to an implantable battery free cardiac pacing. The design realizes an efficiency at a significant power of 12 dBm. A dual-band (2.45 and 5.8 GHz) RF rectifier is deployed for WPT energy harvesting (EH) in24. The design utilizes a HSMS2860 diode for a high input power source. At an input power of 12.0 dBm, the highest efficiency of 63.0% and 54.80% is realized. A 2.32 and 3.48 GHz Class-F mid-field system comprising a single-shunt diode is demonstrated by the authors in25. An implantable triple-band stacked single-shunt rectifier with a radial construction is introduced by the authors in26. Only one specified frequencies can be deployed for WPT’s, wake-up and sleep controllers, and data telemetry. The authors in27 present a triple band rectifier for biotelemetry applications at white space Wi-Fi band. The designed is applied to realized a 390 mV wirelessly and achieved 48.00%, 52.00%, 45.00% RF-to-DC PCE at -5 dBm. The authors in28 presents a triple band (1.95, 2.70, and 5.80 GHz) rectifier through multi-stepped transmission lines for WPT and RF energy harvesting (RFEH). The large electrical size described in the design increases the overall size of the implants. The studies showed that the technique can deliver peak efficiency of 62.2%, 59.40%, and 48.9% at an input power of 0 dBm. The researchers in29 described their work concerning a two-port, five-band RF rectifier. The physical dimensions of the rectifier were measured to be 75 mm \(\times\) 75 mm, and the experimental results indicated that it attained an average power conversion efficiency of 23.2% when subjected to an input power of -20 dBm. The authors in30 and31 introduced a quad-band and six-band RF harvester. This system demonstrated a PCE of 15% and 67% when subjected to an input power of -20 and -5 dBm, respectively. However, the reported -10 dB operational bandwidth was relatively narrow across all six and fourth operating frequencies. The use of a single dual-diode was found to increase the rectifier parasitic capacitance at the diode junction. At the same time, the presence of sixth-order lumped elements MN within the four and three cell branches in30 and31 contributed to a reduction in the overall PCE due to parasitic effects. The researchers in32 presented a seven-band rectifier design operating at (1.80, 2.10, 2.40, 2.60, 3.50, 4.90, and 5.80 GHz). The rectifier was implemented using an SMS7630 diode. This work achieved a peak PCE of 64% when exposed to 4 dBm input power. The rectifier design achieved peak PCE at high power and a large dimension. However, there is limited harnessing of available RF power at frequencies of 3.50, 4.90, and 5.80 GHz. Also, most of the rectifiers that have been studied in the literature between20 and25 use either a single or dual operating frequency (\(f_{o}\)) with a narrow band. Besides the intricate circuitry and significant power is expected for the circuit to function in the implants efficiently. The large electrical size lowers the overall efficiency of the designs shown by the authors in26,27,28,29,30,31, and32 for low power application.

This paper proposes an implantable multiband RF rectifier for microwave WPT operating at 1.830 and 2.100 GHz and a broad white space ISM band (2.380 - 2.80 GHz). The 2.45 GHz ISM band was chosen because it is among the license-free bands. The proposed design is established around an L-shunt \(\lambda _{g}\)/8 MN via an impedance transformer (ITx) between the four-unit cells. The rectifier’s operating frequencies are systematically matched to the four cells, accordingly. The proposed design improves the operational BW and size by positioning the L-shunt between a series inductor and a radial shunt stub. This keeps the capacitance at the branch of the rectifier to a minimum, which improves the overall PCE of the RF rectifier. Hence, the proposed design demonstrates a unique sequential matching technique that simplifies the circuit complexity over a wide range of harvested frequencies, high PCE, good \(V_{DC}\) capability, compact size, and applicability to power low-power biomedical implantable devices and is a promising option for wireless power transfer (WPT) than single-band WPT systems.

The proposed technique is implemented across the four operating frequencies using a unique architecture shown in Fig. 2. Cell-1, Cell-2, Cell-3, and Cell-4 are the four parts of the design, each configured with an L-shunt MN, a radial stub, and a series inductor. The proposed MN is employed to convert the rectifying unit’s (RU) complex impedance into the source impedance by ITx matching TL7(TL8), TL17(TL16), TL20(TL21), and TL32(TL31). Three sets of line connections (TL9-TL10), TL11, and a radial stub of length Lr1 across D1 are used to realize the MN in Cell-1. To match D2, an L-section (TL14-TL15) MN was introduced in Cell-2 with the help of TL13 and the Lr2 stub. Cell-3 comprises an L-section (TL25-TL24), TL25, and an Lr3 stub for matching D3. Whereas D4 matching is achieved using L-sections TL29-TL30, TL28, and the Lr4 stub. Both sections are implemented around a single series (SSr) diode configuration. A suitable rectifying diode evaluation for transformation is one of the most crucial parts of establishing the RF-rectifier for extracting the RF signal. This design is based on the HSMS2850 Schottky diodes D1, D2, D3, and D4. It was made using the small-outline transistor (SOT)-323 circuit layout method. The SOT-323 approach of circuit architecture was used in its manufacturing process. Because of its low junction capacitance of 0.18 pF and low sensitivity of 150 mV, the diode is a potential device for low-power applications. The SSr diodes are coupled to an inductor and a radial stub in the proposed design, allowing for low-power operation over a broad frequency range (Table 1). The use of the short circuited-stubs allows for a more smooth flow of DC into the circuit.

EM model layout of the proposed wideband RF-rectifier.

An analytical study was conducted on the matching performance to ensure the proposed model functions optimally. The optimal performance of the pre-design RF-rectifier is then estimated using a source pull simulation in an advance design system (ADS). With the pre-design analysis’s help, the load’s (\(R_{L}\)) the capacitor’s (C) appropriate size and can be inspected. The proposed topology performs better when the power level across each cell is between -5 and 2 dBm. At a 0 dBm input power level, the equivalent impedances for Cell-1, Cell-2, Cell-3, and Cell-4 are presented in Table 2. The preliminary design demonstrates an improvement at 330 pF and 5 k\(\Omega\). Each cell is designed for a particular frequency range: Cell-1 (\(f_{1}\) = 1.83 GHz), Cell-2 (\(f_{2}\) = 2.1 GHz), Cell-3 (\(f_{3}\) = 2.45 GHz), Cell-4 (\(f_{4}\) = 2.66 GHz). It is important for the MN to keep the imaginary side of each diode stable across the frequencies \(f_{1}\), \(f_{2}\), \(f_{3}\), and \(f_{4}\). This keeps the impedance mismatch of \(Z_{inp}\), \(Z_{inq}\), \(Z_{inr}\), and \(Z_{ins}\) in the RU to about 50 \(\Omega\).

First, an L-shunt MN connected to TL7 is modeled in the architecture of Cell-1’s impedance matching network (IMN) at \(f_{1}\). The Upper (\(f_{1u}\)) and lower (\(f_{1l}\)) frequencies are related in a complex conjugate form by the TLs ((TL9-TL10), TL11), to match the admittances at the common node. Hence, \(Z_{9}\) \(|\) \(f_{1l}\) = [\(Z_{9}\) \(^{*}\) \(|\) \(f_{1u}\)], \(Z_{11}\) \(|\) \(f_{1l}\) = [\(Z_{11}\) \(^{*}\) \(|\) \(f_{1u}\)], \(Z_{8}\) \(|\) \(f_{1l}\) = [\(Z_{8}\) \(^{*}\) \(|\) \(f_{1u}\)]. At a particular operating frequency, in the direction of the load where the RF signal is being cut off by the DC pass filter (DPF), the impedance should be infinite. Therefore, \(Z_{9}\) \(|\) \(f_{1l}\) = [\(Z_{9}\) \(^{*}\) \(|\) \(f_{1u}\)] = 0 The TL7 parameters (\(\theta _{7}\) and \(Z_{7}\)) change the odd imaginary part of \(Z_{7}\) into a symmetrical form and keep the real part in balance.

Assume that the values \(Z_{inp}\) at \(f_{1l}\) and \(f_{1u}\) are governed by: \(Z_{p1}\) \(|\) \(f_{1l}\) = \(R_{Lp1}\) \(+\) \(X_{Lp1}\) and \(Z_{p1}\) \(|\) \(f_{1u}\) = \(R_{Lp2}\) \(+\) \(X_{Lp2}\). Then:

where \(\theta _{p1}\) denotes for the electrical length of the line at \(f_{1l}\) and \(f_{1u}\). These frequencies are controlled by a frequency ratio (e), such that \(f_{1l}\) \(f_{1u}\). Therefore, \(f_{1u}\) = e \(\times\) \(f_{1l}\). Thus, \(\theta _{p1}\) \((f_{1u})\) = e \(\times\) \(\theta _{p1}\) \((f_{1l})\) = \(e\theta _{p1}\). The complex conjugate of \(Z_{inp}\) becomes \(Z_{inp}\) \(|\) \(f_{1l}\) = {\(Z_{inp}\) \(^{*}\) \(|\) \(f_{1u}\)} through the TL7 transformation. The admittance (Y\(_{p1}\)) is then conjugated using the derived parameters \(Z_{p1}\) and \(\theta _{p1}\).

d is an integer chosen to improve the design process. Both \(Z_{7}\) and \(\theta _{7}\) are calculated to have impedances of 56.86 \(\Omega\) and 61.85\(^o\), using Eqs. (3 and 4), respectively, when d = 3. At first, \(Z_{inp}\), \(Z_{inq}\), \(Z_{inr}\), and \(Z_{ins}\) were used in calculating the pre-design model in ADS, to determine the values of the ITx (TL7, TL17, TL20, and TL32), as shown in Table 3. TL7 is further segmented into the TL8 with the addition of an inductor (\(L_{q}\)) coupled to the ITx. The concept is applied between (TL17 and TL16), (TL20 and TL21), and (TL32 nad TL31). Inductive lumped components have been added to the two parts to boost the RF signal received by the RU with minimal TL length and loss. On the other hand, the TL11 at \(f_{1l}\) and \(f_{1u}\) exhibits the conjugated connection found in TL7. This is attained if TL7’s (\(\theta _{11}\)) at \(f_{1l}\) satisfies the condition in Eq. (5).

The conjugate matching between the two frequencies generates TLIN admittances. Hence, at the source terminal, the impedance \(Z_{s}\) requires that the real element of Y\(_{11}\) be equal to that of Y\(_{7}\) via TL7; consequently:

where \(G_{7}\) stands for \(Y_{7}\)’s real element. Eqs. (5 and 6) show that, for frequencies \(f_{1l}\) and \(f_{1u}\), \(Z_{11}\) and \(\theta _{11}\) are 85.25 \(\Omega\) and 20.62\(^o\), respectively.

The radial stub Lr1 and TL9 make up for \(Y_{inp}\)’s imaginary impedance, keeping the real impedance at \(Y_{in7}\) = \(1/Z_{in7}\). Therefore, the TL9 is represented by A(\(Z_{9}\), \(\theta _{9}\) at \(f_{1l}\)) and \(e \theta _{9}(f_{1l})\). In addition, the entire short-circuited L-shunt stub is guided by \(Y_{in9}(f_{1l})\) = \(1/jZ_{9} \tan e\theta _{9}(f_{1l})\). It is desirable for the admittance of TL9 to be odd-symmetric at \(f_{1l}\) and vary inversely with the imaginary part of \(Y_{in7}\).This effectively reduces the imaginary part to nearly zero. Loading TL7 into G + jB and G - jB conjugates at \(f_{1l}\) and \(f_{1u}\) transforms these admittances.

The short-circuited L-shunt stub’s admittance may then be enhanced with the following:

From Equation 7:

where:

Equations (8 and 9) calculate \(Z_{9}\) and \(\theta _{9}\) to be 95.12 \(\Omega\) and 67.40\(^o\), respectively. Selecting the appropriate \(Z_{i}\) and \(\theta _{i}\) throughout the design process helps prevent uncontrolled and pointless characteristic impedance.

Several stubs comprising linked microstrip curve bend (MCURVE), also known as MC, radial stubs, and stepped-impedance lines, are used in ADS to reduce manufacturing limitations and enhance design performance. The TL9 is then partitioned into the TL10 through MC4. Also, a radial stub Lr is integrated into the susceptance block TL9 to enhance the design’s operational BW. The stub, whose Lr1 is set at 0.6 mm and optimized with a 78\(^o\) bend angle, gives the design an extra degree of freedom.

Similar to how Cell-1’s parameters were modeled, Cell-2 (T17-TL16, TL13, TL8, TL15-TL14, and MC5), Cell-3 (TL20-TL21, TL25, TL24-25, MC6), and Cell-4 (TL31-TL232, TL28, TL29-30, MC7) parameters were also established by using Eqs. (1 to 9). A series of inductive matchings (\(L_{a}\), \(L_{b}\), \(L_{c}\), and \(L_{d}\)) are deployed towards the diode’s anode and between the ITx, across the four cell blocks. The first designs of \(L_{a}\), \(L_{b}\), \(L_{c}\), and \(L_{d}\) were made using the ideal palette in ADS at 1.5, 1.7, 4.5, and 6 nH, respectively. The inductors were adjusted between 0.5 and 10 nH to make up for the effect of the transmission line on the design. More optimization was then applied to the proposed circuits. A relevant muRata components from the ADS library was added to replace the elements of the ideal inductor. The low-power LQP03TG1N0B02 and LQP03TG5N1H02 series model with 0603 layouts is used for optimal inductor performance in the design, as depicted in Fig. 1. In order to reduce the amount of interference in the circuit, the capacitor C is used to “shunt” the diode D4. The two capacitor filters from muRata have the model number GCH1555C1H331JE01 from the 0402 families.

A 1.60 mm thick FR-4 substrate (tangent loss = 0.02 and dielectric constant = 5.6) was used as the basis for the design. The proposed implantable RF rectifier has integrated TL3, TL4, TL5, TL12, TL26, and TL28 to improve the design architecture’s functionality. A 50 \(\Omega\) TL terminates the four cell block configurations. This is followed by optimization and fine-tuning of the complete RF-rectifier unit, as presented in Fig. 2. The specifications and attributes of the proposed RF rectifier is reported in Table 1.

The proposed design’s simulated and measured: (a) Reflection roefficient (\(|S_{11}|\)). (b) RF-to-dc PCE against frequency at different \(P_{in}\).

Figure 3a compares the simulated reflection coefficient \(|S_{11}|\) results of the proposed implantable rectifier and the measured results in free space and the encapsulated minced pork. The -10 dB simulated (measured) fractional percentage BW (FBW) across the major operating frequencies are 4.91% (5.53%), 3.83% (4.34%), and 11.77% (11.44%) for the WiFi white space region. A good simulated (measured) BW is demonstrated by the proposed multiband RF-rectifier, amounting to 90 MHz (100 MHz) for 1.83 GHz, 80 MHz (90 MHz) for 2.10 GHz, 300 MHz (290 MHz) for 2.45 GHz.

The RF input power for this test configuration was generated with the help of a 12 GHz signal generator (APSIN12G) and a (ZHL-4240\(^+\)) power amplifier. The \(V_{DC}\) from the measuring equipment is determined using a digital multimeter (DMM) made by Sanwa Technology. The relationship between simulated (measured) RF-to-DC PCE against frequency for 0, -10, -20, and -30 dBm is presented in Fig. 3b. RF-to-DC PCE of the proposed RF rectifier is expressed by: \(P_{DC}\)/\(P_{in}\). The \(P_{DC}\) total power is calculated by the \(V_{DC}\) passing through the load \(R_{L}\). At first, there was a deviation in the response of the PCE measurements from the prototype’s fabrication. In comparison to the simulated PCE results at 64.32%, 74.20%, 73.00%, and 54.90% at four operating frequencies (\(f_{o}\)), 1.83, 2.10, 2.45, and 2.66 GHz, and 2 dBm of input power, respectively, the initial prototype achieved efficiencies of 56.10%, 65.14%, 62.21%, and 44.11%. This could be impacted by losses like the SMA source, part’s accuracy (tolerance), cables, the leads, and TL that interconnect the model’s elements. Also, the dispersed TL, lumped elements’ parasitic capacitance, and phase shift at high frequency can introduce measurement errors. Therefore, the proposed design uses parameter component models to manage the parasitic effect at high frequencies. ADS’s ML optimization and momentum modeling method was used to addressed the problems with the SMA source, connecting lines (TL3 – TL33, TL1 – TL2, and TL), Vias, and other critical parasitic elements. The reactance of the capacitors was obtained from the muRata element model to mitigate these constraints. The successive model adjustments led to the final version of the prototype. The measured and simulated findings agree with one another, as shown in Fig. 3a. From Fig. 3b, over 55% RF-to-DC PCE was recorded at 0 dBm, and 11% was also observed at -20 dBm, between 1.80 and 2.55 GHz. The efficiency of the proposed prototype at -20 dBm was investigated to show the design’s significance at low power levels. Hence, at the four operating frequencies, the rectifier reached a maximum PCE of 20.60%, 20.80%, 16.75%, and 13.10%. Figure 4a illustrate the proposed rectifier \(V_{DC}\) as a function of input power. Also, Fig. 4b shows how the performance of a simulated and measured RF rectifier changes with the amount of \(P_{in}\). For the four operating frequencies, the proposed RF rectifier reached a maximum simulated (measured) RF-to-DC PCE at an input power of 2 dBm at: 64.32% (63.60%), 74.20% (72.70%), 73.00% (72.12%), 55.00% (53.60%). The measurement setups of the proposed RF rectifier prototype is depicted in Fig. 5. There is a slight difference between what was simulated and what was measured. This is because of the effect of component tolerances and the phase shift on the improved prototype. A summary of the simulated and measured results is reported in Table 4.

In this study, we use a spectrum analyzer to appraise the magnitude of the RF signal captured from different EM sources in the test surroundings. The proposed RF rectifier is subjected to experimental evaluation by utilizing a rectenna system deployed in an open space setting. The rectenna facilitates the evaluation of the RF rectifier within its surrounding ambient environment. Simultaneously, the rectenna serves as an effective means to monitor the RF power’s strength through the analyzer. The evaluation of the rectenna system involved the integration of an RF rectifier with a wideband circular antenna designed to operate efficiently in the frequency range of 1.550 to 3.140 GHz. The antenna exhibited a peak realized gain ranging from 1.93 to 3.20 dB. When utilized in its surrounding environment, the rectenna system successfully generated a \(V_{DC}\) with a magnitude of 0.44 V, as depicted in Fig. 6. The findings demonstrate that, under free-space conditions, the RF-to-DC PCE reaches approximately 38.80%.

Simulated and measured: (a) Output DC Voltage (\(V_{DC}\)) against \(P_{in}\). (b) RF-to-dc PCE against \(P_{in}\).

The measurement setups of the proposed RF rectifier prototype.

Table 5 shows how the proposed RF rectifier measures up against recent works that have been studied in the literature. While a unique L-shunt \(\lambda _{g}\)/8 MN technique is employed in this study, it is essential to note that the proposed design has improved operational BW, lower electrical length and higher performance at low input power. The authors of20,21, and22 recorded a single-band rectifier that is fairly narrow. The proposed design record a good FBW of 11.44% across the white space ISM band. Increased PCE at a high \(P_{in}\) of 12 dBm was shown by the authors in23. Along with the authors’ illustration of high \(P_{in}\) (12 and 5 dBm) in24 and25, respectively the longer electrical lengths also exhibit low RF-to-DC PCE. The authors in26,27, and8 demonstrate a multiband RF rectifier that operates at low \(P_{in}\) between -5 and 5 dBm, at the cost of considerable electrical length. At 2 dBm, our proposed design achieved 72.7% RF-to-DC PCE. Similarly, the works reported by the authors in29,30,31, and32, a common approach in the reported works involves the implementation of a dual single diode with a narrow band and a large electrical size. However, this method presents challenges, such as complex circuitry and a high input power requirement to ensure the circuit’s efficient functioning within implants. These design choices reduce overall efficiency and limit the harnessing of available RF power at specific frequencies, as stated in29 at 3.50 GHz and in32 at 3.50, 4.90, and 5.80 GHz. Compared to the work shown in the related literature, the proposed method demonstrates improved compactness and has a shorter electrical length of 0.27\(\lambda _{g}\) \(\times\) 0.29\(\lambda _{g}\). Between 1.80 and 2.55 GHz, the proposed topology reached over 55% RF-to-DC PCE at 0 dBm. For low-power applications, this work shows an enhanced performance of 20.60%, 20.80%, 16.75%, and 13.10% at -20 dBm for each of the four frequencies, respectively.

The ambiance measurement setups of the proposed RF rectifier prototype.

This study explores a unique RF rectifier design that uses an improved L-shunt \(\lambda _{g}\)/8 using a sequential matching technique. A series inductor and a radial stub incorporated into a distributed MN is applied to match the impedance of the proposed SSr RF rectifier across the four cells. The technique enhanced the design’s BW and compactness and demonstrated its ability to efficiently leverage the frequency domain by employing multi-band operation and displaying a good impedance bandwidth. The proposed multiband RF rectifier prototype realized a simulated (measured) -10 dB BW of 90 MHz (100 MHz) for 1.83 GHz, 80 MHz (90 MHz) for 2.10 GHz, 300 MHz (290 MHz) for 2.45 GHz and FBW of 4.91% (5.53%), 3.83% (4.34%), and 11.77% (11.44%), respectively. The proposed design architecture produced an output \(V_{DC}\) of 1.61 V and a high PCE of 72.7%. The RF rectifier’s measurements on the PCB board were 0.27\(\lambda _{g}\) \(\times\) 0.29\(\lambda _{g}\). Hence, if managed carefully, the proposed design has practical applications in biomedical engineering, opening up possibilities for powering a wide range of implantable medical devices using harvested RF energy.

All data generated or analysed during this study are included in this published article.

Iqbal, A. et al. Biotelemetry and wireless powering of biomedical implants using a rectifier integrated self-diplexing implantable antenna. IEEE Trans. Microw. Theory Tech. 69, 3438–3451 (2021).

Article ADS Google Scholar

Muhammad, S. et al. Compact rectifier circuit design for harvesting GSM/900 ambient energy. Electronics 9, 1614 (2020).

Article Google Scholar

Yang, Y. et al. Lab-on-a-fish: Wireless, miniaturized, fully integrated, implantable biotelemetric tag for real-time in vivo monitoring of aquatic animals. IEEE Internet Things J. 9(13), 10751–10762 (2021).

Article Google Scholar

Mahmood, A. I., Gharghan, S. K., Eldosoky, M. A. & Soliman, A. M. Near-field wireless power transfer used in biomedical implants: A comprehensive review. IET Power Electron. 15, 1936–1955 (2022).

Article Google Scholar

Muhammad, S. et al. Efficient quad-band rf energy harvesting rectifier for wireless power communications. AEU-Int. J. Electron. Commun. 139, 153927 (2021).

Article Google Scholar

Zhao, Z. et al. Parallel, minimally-invasive implantation of ultra-flexible neural electrode arrays. J. Neural Eng. 16, 035001 (2019).

Article ADS PubMed PubMed Central Google Scholar

Fan, B., Rodriguez, A. V., Vercosa, D. G., Kemere, C. & Robinson, J. T. Sputtered porous PT for wafer-scale manufacture of low-impedance flexible microelectrodes. J. Neural Eng. 17, 036029 (2020).

Article ADS PubMed PubMed Central Google Scholar

Yue, Z., Xu, X., Li, S., Zhu, Y. H. & Lin, X. Q. Efficient and compact tri-band rectifier with large frequency ratio for WPT. IEEE Microw. Wirel. Compon. Lett. 32, 1355–1358 (2022).

Article Google Scholar

Al-Hasan, M. et al. Low-profile dual-band implantable antenna for compact implantable biomedical devices. AEU-Int. J. Electron. Commun. 138, 153896 (2021).

Article Google Scholar

Muhammad, S. et al. Harvesting systems for rf energy: Trends, challenges, techniques, and tradeoffs. Electronics 11, 959 (2022).

Article Google Scholar

Koutroulis, E. & Kalaitzakis, K. Design of a maximum power tracking system for wind-energy-conversion applications. IEEE Trans. Ind. Electron. 53, 486–494 (2006).

Article Google Scholar

Agyenim, F., Hewitt, N., Eames, P. & Smyth, M. A review of materials, heat transfer and phase change problem formulation for latent heat thermal energy storage systems (lhtess). Renew. Sustain. Energy Rev. 14, 615–628 (2010).

Article CAS Google Scholar

Wei, C. & Jing, X. A comprehensive review on vibration energy harvesting: Modelling and realization. Renew. Sustain. Energy Rev. 74, 1–18 (2017).

Article MathSciNet Google Scholar

Selim, K. K., Haggag, A., Amer, F. Z., Rady, W. A. & El-Garhy, A. M. A proposed technique for power extraction from acoustic energy scavenging. Int. J. Electron. 105, 1236–1247 (2018).

Article Google Scholar

Muhammad, S. et al. A dual-band ambient energy harvesting rectenna design for wireless power communications. IEEE Access 9, 99944–99953 (2021).

Article Google Scholar

Iqbal, A., Sura, P. R., Al-Hasan, M., Mabrouk, I. B. & Denidni, T. A. Wireless power transfer system for deep-implanted biomedical devices. Sci. Rep. 12, 13689 (2022).

Article ADS CAS PubMed PubMed Central Google Scholar

Shah, S. A. A. & Yoo, H. Radiative near-field wireless power transfer to scalp-implantable biotelemetric device. IEEE Trans. Microw. Theory Tech. 68, 2944–2953 (2020).

Article ADS Google Scholar

Basir, A. & Yoo, H. Efficient wireless power transfer system with a miniaturized quad-band implantable antenna for deep-body multitasking implants. IEEE Trans. Microw. Theory Tech. 68, 1943–1953 (2020).

Article ADS Google Scholar

Agrawal, D. R. et al. Conformal phased surfaces for wireless powering of bioelectronic microdevices. Nat. Biomed. Eng. 1, 1–9 (2017).

Article Google Scholar

Ding, S., Koulouridis, S. & Pichon, L. Implantable wireless transmission rectenna system for biomedical wireless applications. IEEE Access 8, 195551–195558 (2020).

Article Google Scholar

Abdi, A. & Aliakbarian, H. A miniaturized uhf-band rectenna for power transmission to deep-body implantable devices. IEEE J. Transl. Eng. Health Med. 7, 1–11 (2019).

Article CAS Google Scholar

Bakogianni, S. & Koulouridis, S. A dual-band implantable rectenna for wireless data and power support at sub-ghz region. IEEE Trans. Antennas Propag. 67, 6800–6810 (2019).

Article ADS Google Scholar

Liu, J., Huang, M. & Du, Z. Design of compact dual-band rf rectifiers for wireless power transfer and energy harvesting. IEEE Access 8, 184901–184908 (2020).

Article Google Scholar

Bhatt, K., Kumar, S., Kumar, P. & Tripathi, C. C. Highly efficient 2.4 and 5.8 ghz dual-band rectenna for energy harvesting applications. IEEE Antennas Wirel. Propag. Lett. 18, 2637–2641 (2019).

Article ADS Google Scholar

Bui, G. T., Nguyen, D.-A. & Seo, C. A novel design of dual-band inverse class-f shunt-diode rectifier for energy harvesting (Express Briefs, IEEE Transactions on Circuits and Systems II, 2023).

Book Google Scholar

Wang, S. H., Zheng, S. Y., Leung, K. W. & Xia, M. H. A self-matched multi-band rectifier for efficient electromagnetic energy harvesting. IEEE Trans. Circuits Syst. I Regul. Pap. 68, 4556–4565 (2021).

Article Google Scholar

Shen, S., Zhang, Y., Chiu, C.-Y. & Murch, R. A triple-band high-gain multibeam ambient rf energy harvesting system utilizing hybrid combining. IEEE Trans. Ind. Electron. 67, 9215–9226 (2019).

Article Google Scholar

Halimi, M. A., Surender, D., Khan, T., Kishk, A. A. & Rengarajan, S. R. A multistepped transmission line matching strategy based triple-band rectifier for RFEH/WPT applications. IEEE Microw. Wirel. Compon. Lett. 32, 1007–1010 (2022).

Article Google Scholar

Li, Z., Zhang, J.-W., Wang, Y.-C., He, D.-P. & Zhang, C. Two-port five-band rectenna for ultra-low ambient rf energy harvesting. IEEE Antennas Wirel. Propag. Lett. 22, 1972–1976 (2023).

Article ADS Google Scholar

Kuhn, V., Lahuec, C., Seguin, F. & Person, C. A multi-band stacked rf energy harvester with rf-to-dc efficiency up to 84%. IEEE Trans. Microw Theory Tech. 63, 1768–1778 (2015).

Article ADS CAS Google Scholar

Song, C. et al. A novel six-band dual cp rectenna using improved impedance matching technique for ambient rf energy harvesting. IEEE Trans. Antennas Propag. 64, 3160–3171 (2016).

Article ADS Google Scholar

Wang, Y. et al. Efficiency enhanced seven-band omnidirectional rectenna for rf energy harvesting. IEEE Trans. Antennas Propag. 70, 8473–8484 (2022).

Article ADS Google Scholar

Download references

This research was funded by the deputyship of Research & Innovation, Ministry of Education in Saudi Arabia through the project number (IFP – 2022-06). The funders had no role in study design, data collection and analysis, decision to publish, or preparation of the manuscript.

Faculty of Engineering, Centre For Wireless Technology (CWT), Multimedia University, Cyberjaya, 63100, Malaysia

Surajo Muhammad, Jun Jiat Tiang & Mardeni Roslee

Department of Medical Equipment Technology, College of Applied Medical Science, Majmaah University, Al Majmaah, 11952, Saudi Arabia

Mohamed Ibrahim Waly & Amor Smida

Department of Biomedical Engineering and System (formerly) Higher Institute of Engineering-El Shorouk Academy, Cairo Governorate, Egypt

Mohamed Ibrahim Waly

Department of Business Administration, Majmaah University, 11952, Majmaah, Saudi Arabia

Nasser Ali AlJarallah

AlMaarefa University, Riyadh, Saudi Arabia

Nasser Ali AlJarallah

Department of Electrical and Computer Engineering, Laval University, Quebec City, QC, G1V0A6, Canada

Ridha Ghayoula

Microwave Electronics Research Laboratory, Faculty of Mathematical, Physical and Natural Sciences of Tunis, Tunis El Manar University, Tunis, 2092, Tunisia

Ridha Ghayoula & Amor Smida

Consultant, Saudi Consolidated Engineering Company Healthcare Technology Management Administration, King Fahad Medical City, Riyadh, Saudi Arabia

Ahmed S. Negm

Institut National de la Recherche Scientifique (INRS), Montréal, QC, H5A1K6, Canada

Amjad Iqbal

Department of Network and Communications Engineering, Al Ain University, 64141, Al Ain, UAE

Amjad Iqbal

Department of Electronics and Telecommunication Engineering, Ahmadu Bello University, Zaria, 810211, Nigeria

Surajo Muhammad

You can also search for this author in PubMed Google Scholar

All authors contributed equally. All authors reviewed the manuscript.

Correspondence to Mohamed Ibrahim Waly or Amjad Iqbal.

The authors declare no competing interests.

Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.

Reprints and Permissions

Muhammad, S., Waly, M.I., AlJarallah, N.A. et al. A multiband SSr diode RF rectifier with an improved frequency ratio for biomedical wireless applications. Sci Rep 13, 13246 (2023). https://doi.org/10.1038/s41598-023-40486-x

Download citation

Received: 16 March 2023

Accepted: 10 August 2023

Published: 15 August 2023

DOI: https://doi.org/10.1038/s41598-023-40486-x

Anyone you share the following link with will be able to read this content:

Sorry, a shareable link is not currently available for this article.

Provided by the Springer Nature SharedIt content-sharing initiative

By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.